• Cylinders ST & NW Series
    Cylinders ST & NW Series
    Comments Off on Cylinders ST & NW Series

    These ST Series standard duty cylinders, they have 3000 PSI and a 2″ – 6″ bore and the NW Series are the medium duty . They have a 2500 PSI and bore size of 2″ to 4″. . The rod seals are polyurethane polypak. The piston seals are glass filled teflon with oring expander ….

    Read more
  • Cylinders UT Series
    Cylinders UT Series
    Comments Off on Cylinders UT Series

    These are some heavy duty cylinders, they have 3000 PSI and a 2″ – 12″ bore. The rod seals are polyurethane polypak. The piston seals are glass filled teflon with oring expander and bronze filled teflon ear bands. Ports are SAE straight thread oring. There are some other features you can have added to your…

    Read more
  • Designs of a Diaphragm Seal
    Designs of a Diaphragm Seal
    Comments Off on Designs of a Diaphragm Seal

    These flexible membranes that seal and isolate an enclosure. The flexible nature of this seal allows pressure effects to cross the barrier but not the material being contained. Common uses for diaphragm seals are to protect pressure sensors from the fluid whose pressure is being measured. There are some usual designs and they are flat,…

    Read more
  • Series C101/C102 Hydraulic Pump & Motors for Dump Trucks and Trailers
    Series C101/C102 Hydraulic Pump & Motors for Dump Trucks and Trailers
    Comments Off on Series C101/C102 Hydraulic Pump & Motors for Dump Trucks and Trailers

    These pumps are built on a P30 and P50 frames. They have one piece drive shaft and gears that are held up by roller bearings. It has pressure balance thrust plates give a seal that has stable sealing thru out the pump. The relief valve gives the pump and the cylinder circuit much needed protection….

    Read more
  • Two Position – Three Way Float Position Valve
    Two Position – Three Way Float Position Valve
    Comments Off on Two Position – Three Way Float Position Valve

    Valve float is an adverse condition which can occur at high engine speeds when the poppet valve in an internal combustion engine valve train do not properly follow the closure phase of the cam lobe profile. This reduces engine efficiency and performance. There is also a significant risk of severe engine damage due to valve…

    Read more
  • Series NSD20                 Hydraulic Pump
    Series NSD20 Hydraulic Pump
    Comments Off on Series NSD20 Hydraulic Pump

    This is a tandem pump that has a flow sensitive unloading vlave and power for a port on the unloading pump. It has a main and secondary discharge ports that either pump is changed to the main port when it is at it’s lowest speed. When it is at an intermediate speed, one of the…

    Read more
  • Hydraulic Remote Controllers Codes & Technical Data
    Hydraulic Remote Controllers Codes & Technical Data
    Comments Off on Hydraulic Remote Controllers Codes & Technical Data

    Maximum input Pressure 650 psi 44.8 bar Maximum Return Line Pressure 50 psi 3.5 bar Maximum Control Flow 5gpm 19lpm Viscosity Flange 80-1800 SUS 15-380 cSt Oil Temperature Flange -4F to 150F -20C to 70C Weight Dual Function 4.0 lbs 1.8 kg Single Function 5.0 lbs 2.3 kg Foot Pedal 8.0 lbs 3.6 kg Filtration…

    Read more
  • Hydraulic Oil Remote Controllers
    Hydraulic Oil Remote Controllers
    Comments Off on Hydraulic Oil Remote Controllers

    Joystick Controller These joysticks are made to control two different applications while using one controller. You can use a ball knob, pistol grip that has a electric switch, a pilot joystick and a toggle switch. Foot pedal controller gives the person operating a better comfort to control this with their foot. You can also install…

    Read more
  • Miniature Axial Piston Pumps
    Miniature Axial Piston Pumps
    Comments Off on Miniature Axial Piston Pumps

    These pumps are small in size, capable of different applications, productivity, power and speed. They are useful in automotive, marine, medical and military. Some characteristics of these pumps are : .1 to .865 displacement per rotation made for open circuit systems fixed displacement – output is limited by the motor speed functional temperatures can go…

    Read more
  • Lubricating Pumps That Are Built For Charge & Recirculation Circuits
    Lubricating Pumps That Are Built For Charge & Recirculation Circuits
    Comments Off on Lubricating Pumps That Are Built For Charge & Recirculation Circuits

    Lubricating charge pumps turn out lubricating oil to bearings, gears and other parts. The oil acts as a coolant for the clutch plate and brakes. The operating pressure is around 300 PSI and the relief valve setting to 500 PSI when cold weather you need to start up. You have scavenge pumps take oil from…

    Read more

Back to Top