• DR Series Hydraulic Motors
    DR Series Hydraulic Motors
    Comments Off on DR Series Hydraulic Motors

    If you need a medium heavy duty motor then this is the unit for your heavy duty fluid operations. These motors off a three zone, orbiting disk valve that include a spring biased face seal. This motor uses a Rollor Stator format. It uses rollers for significant sealing points of the rotor assy. By using…

    Read more
  • RE Series Hydraulic Motor
    RE Series Hydraulic Motor
    Comments Off on RE Series Hydraulic Motor

    These are medium heavy duty motors. When pressure starts to ramp up during start up, the balance plate starts in and gives low internal leakage for the utmost starting torque. The roller stator is known to be apart of these motors makeup. This type of application uses the rollers for sealing certain points of the…

    Read more
  • SP-20A Series Gear Pump
    SP-20A Series Gear Pump
    Comments Off on SP-20A Series Gear Pump

    These pumps are very reliable and have even pressure loading that will allow small dispersion. The thru bore will give you an alignment of pump element that gives you an even bearing load. This little pump offers high pressure operation. With an addition of gear teeth it has diminished the flow pulsation and reduced the…

    Read more
  • Series 25X Hydraulic Pump
    Series 25X Hydraulic Pump
    Comments Off on Series 25X Hydraulic Pump

    On the performance data it shows gear widths, but if you need different sizes here is how to do that, multiply vales in the tables below by the actual gear width. On single unit assy. codes you will need to put together shaft end cover, port end cover, gear housing and drive shaft codes. A…

    Read more
  • P330/P350/P365 Hydraulic Pumps
    P330/P350/P365 Hydraulic Pumps
    Comments Off on P330/P350/P365 Hydraulic Pumps

    These types of pumps and motors were made to endure long lengths of run time while running pressures at 3500 psi. The mountings are a SAE B 2 and 4 bolt flange and a SAE C 2 and 4 bolt flange. The shafts and covers on them can use a single or twin shaft seal….

    Read more
  • C101/102 Hydraulic Pump for Heavy Duty Trucks
    Comments Off on C101/102 Hydraulic Pump for Heavy Duty Trucks

    These pump are widely used on dump trucks, tractor trailers and heavy duty trucks. They have a one piece drive shaft and gears made of steel, which are help up by roller bearings. It also has pressure balanced thrust plates that give a seal for constant efficiency and hold up to the pumps reliability. There…

    Read more
  • Flow Divider Proportional Type Pressure Compensated That Can Have a Combiner Attachment Added
    Flow Divider Proportional Type Pressure Compensated That Can Have a Combiner Attachment Added
    Comments Off on Flow Divider Proportional Type Pressure Compensated That Can Have a Combiner Attachment Added

    You have model PD and PDC, that can split a single flow of hydraulic oil using these units. The flow percentage coming from the outlet ports stay the same even in load differences in between the ports. Most of these ratios are set at the factory but you can have them adjusted to 90/10 if…

    Read more
  • Directional Control Valves that have Solenoid Operation
    Directional Control Valves that have Solenoid Operation
    Comments Off on Directional Control Valves that have Solenoid Operation

    Series valve circuits lighten the pump flow to the tank when all the 4 ways are in the midpoint position. Pump flow goes thru each of the valves, then the pressure drops additive in. They also have the potential to give the two valves a positive motion of being two functions by applying the exhaust…

    Read more
  • Six Ported Two Position Selector Valve Model DS
    Six Ported Two Position Selector Valve Model DS
    Comments Off on Six Ported Two Position Selector Valve Model DS

    The selector valve makes the flow of the oil go to two different circuits. It will allow the ports of two double acting cylinders that have a one four way control valves or four single acting cylinders that have a two two three way control valves. You will need to decide which hydraulic circuit before…

    Read more
  • RS Series Hydraulic Pumps
    RS Series Hydraulic Pumps
    Comments Off on RS Series Hydraulic Pumps

    These types of pumps can be changed out with MG and MF, Charlynn H/S and Danfoss OMP/OMR, as well as Parkers. Features on these pumps are that they have a modified driven link splines for less chipping, match ground shaft to housing fit, viton shaft seal, three zone rotor set and closed end keyaway. You…

    Read more

Back to Top